# RGB Matrix Lighting

## Driver configuration

### IS31FL3731

There is basic support for addressable RGB matrix lighting with the I2C IS31FL3731 RGB controller. To enable it, add this to your `rules.mk`:

    RGB_MATRIX_ENABLE = IS31FL3731

Configure the hardware via your `config.h`:

	// This is a 7-bit address, that gets left-shifted and bit 0
	// set to 0 for write, 1 for read (as per I2C protocol)
	// The address will vary depending on your wiring:
	// 0b1110100 AD <-> GND
	// 0b1110111 AD <-> VCC
	// 0b1110101 AD <-> SCL
	// 0b1110110 AD <-> SDA
	#define DRIVER_ADDR_1 0b1110100
	#define DRIVER_ADDR_2 0b1110110

	#define DRIVER_COUNT 2
	#define DRIVER_1_LED_TOTAL 25
	#define DRIVER_2_LED_TOTAL 24
	#define DRIVER_LED_TOTAL DRIVER_1_LED_TOTAL + DRIVER_2_LED_TOTAL

Currently only 2 drivers are supported, but it would be trivial to support all 4 combinations.

Define these arrays listing all the LEDs in your `<keyboard>.c`:

	const is31_led g_is31_leds[DRIVER_LED_TOTAL] = {
	/* Refer to IS31 manual for these locations
	 *   driver
	 *   |  R location
	 *   |  |      G location
	 *   |  |      |      B location
	 *   |  |      |      | */
	    {0, C1_3,  C2_3,  C3_3},
	    ....
	}

Where `Cx_y` is the location of the LED in the matrix defined by [the datasheet](http://www.issi.com/WW/pdf/31FL3731.pdf) and the header file `drivers/issi/is31fl3731.h`. The `driver` is the index of the driver you defined in your `config.h` (`0` or `1` right now).

###  IS31FL3733

There is basic support for addressable RGB matrix lighting with the I2C IS31FL3733 RGB controller. To enable it, add this to your `rules.mk`:

    RGB_MATRIX_ENABLE = IS31FL3733

Configure the hardware via your `config.h`:

	// This is a 7-bit address, that gets left-shifted and bit 0
	// set to 0 for write, 1 for read (as per I2C protocol)
	// The address will vary depending on your wiring:
	// 00 <-> GND
	// 01 <-> SCL
	// 10 <-> SDA
	// 11 <-> VCC
	// ADDR1 represents A1:A0 of the 7-bit address.
	// ADDR2 represents A3:A2 of the 7-bit address.
	// The result is: 0b101(ADDR2)(ADDR1)
	#define DRIVER_ADDR_1 0b1010000
	#define DRIVER_ADDR_2 0b1010000 // this is here for compliancy reasons.

	#define DRIVER_COUNT 1
	#define DRIVER_1_LED_TOTAL 64
	#define DRIVER_LED_TOTAL DRIVER_1_LED_TOTAL

Currently only a single drivers is supported, but it would be trivial to support all 4 combinations. For now define `DRIVER_ADDR_2` as `DRIVER_ADDR_1`

Define these arrays listing all the LEDs in your `<keyboard>.c`:

	const is31_led g_is31_leds[DRIVER_LED_TOTAL] = {
	/* Refer to IS31 manual for these locations
	 *   driver
	 *   |  R location
	 *   |  |       G location
	 *   |  |       |       B location
	 *   |  |       |       | */
	    {0, B_1,    A_1,    C_1},
	    ....
	}

Where `X_Y` is the location of the LED in the matrix defined by [the datasheet](http://www.issi.com/WW/pdf/31FL3733.pdf) and the header file `drivers/issi/is31fl3733.h`. The `driver` is the index of the driver you defined in your `config.h` (Only `0` right now).

From this point forward the configuration is the same for all the drivers. 

	const rgb_led g_rgb_leds[DRIVER_LED_TOTAL] = {
	/* {row | col << 4}
	 *    |           {x=0..224, y=0..64}
	 *    |              |               modifier
	 *    |              |                 | */
	    {{0|(0<<4)},   {20.36*0, 21.33*0}, 1},
	    {{0|(1<<4)},   {20.36*1, 21.33*0}, 1},
	    ....
	}

The format for the matrix position used in this array is `{row | (col << 4)}`. The `x` is between (inclusive) 0-224, and `y` is between (inclusive) 0-64. The easiest way to calculate these positions is:

    x = 224 / ( NUMBER_OF_ROWS - 1 ) * ROW_POSITION
    y = 64 / (NUMBER_OF_COLS - 1 ) * COL_POSITION

Where all variables are decimels/floats.

`modifier` is a boolean, whether or not a certain key is considered a modifier (used in some effects).

## Keycodes

All RGB keycodes are currently shared with the RGBLIGHT system:

	* `RGB_TOG` - toggle
	* `RGB_MOD` - cycle through modes
	* `RGB_HUI` - increase hue
	* `RGB_HUD` - decrease hue
	* `RGB_SAI` - increase saturation
	* `RGB_SAD` - decrease saturation
	* `RGB_VAI` - increase value
	* `RGB_VAD` - decrease value
	* `RGB_SPI` - increase speed effect (no EEPROM support)
	* `RGB_SPD` - decrease speed effect (no EEPROM support)


	* `RGB_MODE_*` keycodes will generally work, but are not currently mapped to the correct effects for the RGB Matrix system

## RGB Matrix Effects

These are the effects that are currently available:

	enum rgb_matrix_effects {
	    RGB_MATRIX_SOLID_COLOR = 1,
	    RGB_MATRIX_ALPHAS_MODS,
	    RGB_MATRIX_DUAL_BEACON,
	    RGB_MATRIX_GRADIENT_UP_DOWN,
	    RGB_MATRIX_RAINDROPS,
	    RGB_MATRIX_CYCLE_ALL,
	    RGB_MATRIX_CYCLE_LEFT_RIGHT,
	    RGB_MATRIX_CYCLE_UP_DOWN,
	    RGB_MATRIX_RAINBOW_BEACON,
	    RGB_MATRIX_RAINBOW_PINWHEELS,
	    RGB_MATRIX_RAINBOW_MOVING_CHEVRON,
	    RGB_MATRIX_JELLYBEAN_RAINDROPS,
	    RGB_MATRIX_DIGITAL_RAIN,
	#ifdef RGB_MATRIX_KEYPRESSES
	    RGB_MATRIX_SOLID_REACTIVE,
	    RGB_MATRIX_SPLASH,
	    RGB_MATRIX_MULTISPLASH,
	    RGB_MATRIX_SOLID_SPLASH,
	    RGB_MATRIX_SOLID_MULTISPLASH,
	#endif
	    RGB_MATRIX_EFFECT_MAX
	};
    
You can disable a single effect by defining `DISABLE_[EFFECT_NAME]` in your `config.h`:


|Define                                             |Description                                 |
|---------------------------------------------------|--------------------------------------------|
|`#define DISABLE_RGB_MATRIX_ALPHAS_MODS`           |Disables `RGB_MATRIX_ALPHAS_MODS`           |
|`#define DISABLE_RGB_MATRIX_DUAL_BEACON`           |Disables `RGB_MATRIX_DUAL_BEACON`           |
|`#define DISABLE_RGB_MATRIX_GRADIENT_UP_DOWN`      |Disables `RGB_MATRIX_GRADIENT_UP_DOWN`      |
|`#define DISABLE_RGB_MATRIX_RAINDROPS`             |Disables `RGB_MATRIX_RAINDROPS`             |
|`#define DISABLE_RGB_MATRIX_CYCLE_ALL`             |Disables `RGB_MATRIX_CYCLE_ALL`             |
|`#define DISABLE_RGB_MATRIX_CYCLE_LEFT_RIGHT`      |Disables `RGB_MATRIX_CYCLE_LEFT_RIGHT`      |
|`#define DISABLE_RGB_MATRIX_CYCLE_UP_DOWN`         |Disables `RGB_MATRIX_CYCLE_UP_DOWN`         |
|`#define DISABLE_RGB_MATRIX_RAINBOW_BEACON`        |Disables `RGB_MATRIX_RAINBOW_BEACON`        |
|`#define DISABLE_RGB_MATRIX_RAINBOW_PINWHEELS`     |Disables `RGB_MATRIX_RAINBOW_PINWHEELS`     |
|`#define DISABLE_RGB_MATRIX_RAINBOW_MOVING_CHEVRON`|Disables `RGB_MATRIX_RAINBOW_MOVING_CHEVRON`|
|`#define DISABLE_RGB_MATRIX_JELLYBEAN_RAINDROPS`   |Disables `RGB_MATRIX_JELLYBEAN_RAINDROPS`   |
|`#define DISABLE_RGB_MATRIX_DIGITAL_RAIN`          |Disables `RGB_MATRIX_DIGITAL_RAIN`          |
|`#define DISABLE_RGB_MATRIX_SOLID_REACTIVE`        |Disables `RGB_MATRIX_SOLID_REACTIVE`        |
|`#define DISABLE_RGB_MATRIX_SPLASH`                |Disables `RGB_MATRIX_SPLASH`                |
|`#define DISABLE_RGB_MATRIX_MULTISPLASH`           |Disables `RGB_MATRIX_MULTISPLASH`           |
|`#define DISABLE_RGB_MATRIX_SOLID_SPLASH`          |Disables `RGB_MATRIX_SOLID_SPLASH`          |
|`#define DISABLE_RGB_MATRIX_SOLID_MULTISPLASH`     |Disables `RGB_MATRIX_SOLID_MULTISPLASH`     |


## Custom layer effects

Custom layer effects can be done by defining this in your `<keyboard>.c`:

    void rgb_matrix_indicators_kb(void) {
        rgb_matrix_set_color(index, red, green, blue);
    }

A similar function works in the keymap as `rgb_matrix_indicators_user`.

## Additional `config.h` Options

	#define RGB_MATRIX_KEYPRESSES // reacts to keypresses (will slow down matrix scan by a lot)
	#define RGB_MATRIX_KEYRELEASES // reacts to keyreleases (not recommened)
	#define RGB_DISABLE_AFTER_TIMEOUT 0 // number of ticks to wait until disabling effects
	#define RGB_DISABLE_WHEN_USB_SUSPENDED false // turn off effects when suspended
    #define RGB_MATRIX_SKIP_FRAMES 1 // number of frames to skip when displaying animations (0 is full effect) if not defined defaults to 1
    #define RGB_MATRIX_MAXIMUM_BRIGHTNESS 200 // limits maximum brightness of LEDs to 200 out of 255. If not defined maximum brightness is set to 255

## EEPROM storage

The EEPROM for it is currently shared with the RGBLIGHT system (it's generally assumed only one RGB would be used at a time), but could be configured to use its own 32bit address with:

    #define EECONFIG_RGB_MATRIX (uint32_t *)16

Where `16` is an unused index from `eeconfig.h`.

## Suspended state

To use the suspend feature, add this to your `<keyboard>.c`:

	void suspend_power_down_kb(void)
	{
	    rgb_matrix_set_suspend_state(true);
	}

	void suspend_wakeup_init_kb(void)
	{
	    rgb_matrix_set_suspend_state(false);
	}
